Swimming Pool Blog

Winterization also requires you to disconnect the hoses for the pool, pump and filter. Once the winter is over, and the outdoor temperatures begin to rise, it is time to reopen the pool for the summer. Trying to remember where each of the three hoses attach to your filter, pool and pump can quickly spell disaster if you mix up the connections. Correctly hook up your sand filter and pump to your above-ground pool for hours of summer fun. Make sure to locate it near the skimmer and return on your pool. Ensure the ground is level beneath the pump and filer. Place the pump and filter on concrete blocks for additional stability. Pumps can be hardwired to the breaker, or plug into an outdoor receptacle.

How do you hook up hoses to a pool pump and filter?

You will need the pump, the filter which may be sand, D. You will also need a few tools as well to connect the pool hoses and to also connect the PVC plumbing unions that may be on both the pump and filter. You will need a screwdriver to tighten the hose clamps, a pair of channel locks to tighten the PVC plumbing unions and you may also need some Teflon tape to wrap around some of the plumbing fittings if they are loose or worn from the prior years use.

You will also need a bucket so you can prime the pump and start it up after you are all done connecting it. You will also need a source of electrical power for your above ground filter system as well. Once you have gathered the tools, made sure that you have electrical power to the outlet near your filter system you then will want to take the filter and the pump over to the filter area where you will be setting the filter system up.

• Prime filter prior to starting up filter system. DO NOT. FILTER CYCLES POOL WATER WON’T CLEAR UP. 1. Check for algae in pool and Check surface of filter sand for crusting or caking. Remove. BlueWave NE Sandman Filter and Pump Owner’s Manual –

We are having trouble with remembering how to connect everything since we didn’t get to open the pool last season. We are not using the heater or the auto chlorinator as they are both broken. We have a Pentair sand filter that we just cleaned out and replaced the sand with new. I understand the skimmer bottom connects to the front of the pump and that the pool wall is connected to the ‘pool return’, what gets connected to the pvc drain pipes? It has two valve shut offs and do we have to go through the heater?

Sincerely Confused Karin Hi Karin.

Pool Community

You will be delighted with our low prices, personalized customer service and wide selection of quality, brand-name products for pool care and maintenance. We offer safety pool covers in a variety of sizes and with various warranties. You can choose from solid covers for winter, if you prefer.

When using this filter with an Intex swimming pool, these supplies are all that is needed to get the filter up and running. However, when using the Intex Sand Filter with a pool of a different brand, additional fittings will often be necessary. Vacuuming the Pool.

Diy Non- Pressurized Sand Filter for Backyard Pools i have had a few cheap backyard frame pools, and pretty much the “filtration systems” they come with are only good for people that never get in there pool dirty, have no friends, no kids, no dogs, nothing but time to wash or replace the filter constantly, always keep the pool covered, you get the idea. Add Tip Ask Question Step 1: The Basics why do you want a sand filter?

Add Tip Step 2: Parts i didnt really document this very well but its pretty simple. Rest of the Parts now you want somthing that will stop the sand from comming out and only let clean water through. Add Tip Ask Question Step 4: Hows Did It Do? I did ad some algaecide but i never had it work this well, or much at all, so i give credit to the filter. I had to backwash the filter once or twice after a couple days, just like a real sand filter you would reverse flow through the filter washing the sand and whatever has settled on top.

DO not pump that back into your pool obviously, i just disconnected the hose from the IN side of the filter and let the filter spill the dirty water out and flipped the pump from the OUT side of the filter around so it was pushing back into the sand.

Pool Filter Hook Up

A swimming pool filter helps maintain clean and healthy pool water. The pump sends water to the filter, which cleans it out before sending it back out into the pool. Public pools follow certain laws stating that a certain amount of water must go through the filter in a certain amount of time.

Before you connect the pool sand filter into the piping system, you have to assemble the filter. First screw the pressure gauge to the 1/4″ hole on the side of the filter. If the threads aren’t prepared, wrap them with two layers of Teflon tape.

How do I vaccum the pool? I dont know if I turn the Veriflow to out and then where do I hook in the hose?.. Its my girlfriends pool and she just expects me to know. Thanks Oh then you DO need help. You attach the hose to the skimmer inlet. Usually there will be a round plate attched to the hose that fits into the skimmer you may have to remove the basket If you don’t have that round plate on the hose, then you can insert the hose driectly into the bottom of the skimmer.

Before you attach the hose, connect it to the skimmer head on the pole. Submerge the head and hose. Allow to settle to bottom.

Hooking up swimming pool pump/filter to above ground pool?

Top Step 1 Before starting installation, you will need to purchase sand. Use only high rate No. An example is pictured at left.

2. If needed: Set up appointment with a licensed professional to hook up the required electrical to the unit. 3. Using “Step 5:Connecting Your System” as a guide, make the necessary water UV system is almost always found directly after the pool filter. 3. If needed: Set up an appointment with a licensed professional to hook up any.

April 16, Subscribe to our weekly pool maintenance newsletter! Pool season has arrived. You could really go for a swim. But there you are, standing on your patio, staring at a dirty pool cover, wondering what kind of horrors await you underneath it. Every year, thousands of pool owners end up in emergency rooms due to poisoning from pool chemicals. Most of those injuries occurred because people were not wearing protective gear when handling pool chemicals.

Pool cover pump If you click this link and make a purchase, we earn a commission at no additional cost to you. Soft broom If you click this link and make a purchase, we earn a commission at no additional cost to you. Winter cover cleaner If you click this link and make a purchase, we earn a commission at no additional cost to you. Start-up chemical kit If you click this link and make a purchase, we earn a commission at no additional cost to you.

Silicone pool gasket lubricant If you click this link and make a purchase, we earn a commission at no additional cost to you. Thread seal tape If you click this link and make a purchase, we earn a commission at no additional cost to you. Skimmer If you click this link and make a purchase, we earn a commission at no additional cost to you. Garden hose If you click this link and make a purchase, we earn a commission at no additional cost to you.

Fiberglass-Swimming-Pools-DoItYourself

Where can I get info on connecting them. Pretty good plumber but this is confusing. I have tried everything I can think of and can’t get the leaks to stop.

Jun 02,  · Re: Vacuuming with an Intex Sand Filter If you have the Intex skimmer, a ” vacuum hose should fit nicely over the adapter that attaches the skimmer hose to the through-the-wall adapter. It is the adapter in the 5th picture in docchop1’s post above.

How To Install Pool Equipment Tips On How To Install Swimming Pool Equipment As a pool owner it can be difficult to find definitive information about how to install your pool equipment as well which materials you should use and in which order you should install the equipment. In the following pages Swimming Pool Steve talks about many of the commonly used installation materials and processes used to professionally install swimming pool equipment.

Installing your equipment incorrectly can damage the equipment, void your warranty and potentially even be dangerous so be sure to review these sections before installing your own equipment. Pipe materials – Learn from Swimming Pool Steve the difference between pipe materials for swimming pools, which to use when installing your equipment, and how to properly work with each material type. Glue and primer – With grey, clear, blue, yellow, orange and other colors of glue how do you know which one to use for each application?

By reading this section from Swimming Pool Steve on how to select the right glue for any swimming pool equipment installation, that’s how! Threaded connections – When it comes to swimming pool equipment installation you will need to deal with at least a few threaded pipe connections. This section will teach you which materials to use for making connections to your equipment, but more importantly which thread sealants you should NEVER use on pool equipment.

Common pipe fittings – Knowing all of the different kinds of plumbing fittings that you will need to install pool equipment is something that comes with experience. If you are installing your own pool equipment this page on commonly used plumbing fittings in the pool and spa industry will be extremely helpful. Valves and unions – The valves and unions that you use when installing your pool equipment will determine how easy it is to operate your system forever.

Spend some time on this page learning about the commonly used valves and unions as well as their orientation as part of your pool equipment mechanical installation. Pool Equipment Installation Reviews In this ongoing series Swimming Pool Steve looks at some existing pool equipment installations and discusses some of the common installation errors that are encountered in the pool and spa industry.

Learn from these mistakes how to properly install your equipment for ease of use, functionality, and longevity.

Please turn JavaScript on and reload the page.

Pool Cleaning Mistakes to Avoid 1. Vacuuming large debris through skimmer without using a leaf trap. A leaf trap has a bag inside for catching debris and is placed between the end of your pool vacuum hose and the skimmer. It keeps leaves from clogging your skimmer line when you vacuum. It’s OK to not to use a leaf trap as long as you are vacuuming small things that can’t clog the skimmer line, but never go without it when sucking out acorns, sticks, large quantities of leaves, etc.

A swimming pool filter helps maintain clean and healthy pool water. The pump sends water to the filter, which cleans it out before sending it back out into the pool. The pump sends water to the filter, which cleans it out before sending it back out into the pool.

How to convert a Summer Escapes to either a Intex sand pump filter or Intex Saltwater or the combo system. Knowing myself I do not like hose clamps, and the plastic ones included in the kit seem very cheap. I am a big fan with screw type connections. That why I choose to have my system to be all 1. I also do not like 1. I figure now with a bigger pump I like to have everything at 1.

The system I am using: The system of your choosing 2. Drain your pool till you are below the diverter and the skimmer. Remove the diverter valve. Remove the summer escapes skimmer and all internal parts of the skimmer Basket, filter etc. Remove the filter pump.

How to Hook Up a Sand Filter Pump to an Above Ground Swimming Pool

Free from hoses, whips and cords, in-floor pool cleaners operate by creating currents that drive debris towards the skimmer and main drain. Great Idea – and usually an in-floor pool cleaner works flawlessly. They are especially popular for desert pools or pools without a lot of tree leaf litter, as they can become overwhelmed with heavy debris. In addition to keeping the pool clean through smart circulation, in-floor cleaners also help mix pool chemicals faster and equalize water temperature better, than traditional pool cleaners.

I hope you find what you are looking for, if not send me an email! If dirt has begun to collect in one area of the pool that normally stays clean, the first thing to suspect is the overall water flow and operation of the system.

Switch off the power supply to the pool, and attach the vacuum. Fill the hose with water, and attach the skimmer. Adjust the pool water, and block the skimmer baskets. Adjust the pool water to a mid-skimming level. Clean the skimmer baskets, and block them off, except the .

Vacuuming your swimming pool is something that should be done on a weekly basis. Sometimes your swimming pool may not look dirty but there is actually lots of bacteria that you can not see growing on the walls and the floor of the swimming pool. The most important thing you have to remember when vacuuming any swimming pool is that have a good prime is the key to have great suction.

Often many pool owners do not spend enough time properly priming the vacuum hose only to experience hours and hours of problems because they just can not get the debris off of the pool floor. This happens because the swimming pool vacuum has a bad prime. There are a few things that you will need in order to vacuum your pool the correct way.

You will need a vacuum hose that will reach all the way from one end of your pool to the other. You will also need a telescoping vacuum pole, vacuum head and a skimmer vacuum disk. Once you have the items that we listed you will be ready to vacuum your swimming pool manually. The first thing you will want to do before you start vacuuming your pool is to determine if you are going to need a regular vacuum or a swimming pool power vacuum.

The way you can determine this is to gauge how much debris you have in your swimming pool. If your pool is dirty with the normal everyday debris like leaves, some sand and sticks then you probably can get away with just doing a normal vacuum.

Installing a New Hayward Sand Filter


Hello! Do you need to find a sex partner? It is easy! Click here, registration is free!